Marine Genset Sizing Guide for Workboats and Tugs
How to size a genset for a workboat or tug: mapping the electrical load profile, choosing single vs parallel configuration, verifying emissions compliance and class type approval.

Sizing a genset for a workboat or tug is where most newbuild and retrofit projects go wrong - not because the engineering is hard, but because the load profile is guessed instead of measured. An oversized genset runs inefficiently at partial load, wastes fuel and shortens engine life. An undersized one trips when the bow thruster and the galley start at the same time. This guide walks through the sizing process step by step, so the genset you install is the genset your vessel actually needs.
Step 1: Map the Electrical Load Profile
Every consumer on board contributes to the load profile, but not all at once. List every electrical consumer by its rated power and its duty pattern: continuous loads (navigation, communication, refrigeration, lighting), intermittent loads (winches, cranes, bow thruster, galley), and peak-inrush loads (motors starting, compressors). Separate them into at-sea and in-port profiles - the genset must handle both, and the in-port profile is usually the more demanding of the two for workboats.
The result is a load table that shows the peak demand for each operating mode. This table is the foundation for every sizing decision that follows - and the document your class surveyor will ask to see.
Step 2: Apply the Right Margins
Once the peak load is established, apply engineering margins: a loading factor to avoid running the genset at exactly 100% (which shortens engine life), and a future-load allowance for equipment that may be added later. The goal is a genset that runs at 70-80% of its rated capacity under normal conditions - the sweet spot for fuel efficiency and engine longevity. An undersized or oversized genset both cost more over the vessel's life than the correctly sized one.
Step 3: Choose the Genset Configuration
Workboats and tugs typically choose between a single larger genset and two smaller gensets that can be run in parallel. Twin gensets provide redundancy (one can fail without blackouting the vessel), better part-load efficiency (run one at 80% instead of two at 40%), and maintenance flexibility (service one while the other carries the load). The trade-off is higher capital cost and more complex switching. For vessels with high-reliability requirements - tugs under contract to port authorities, offshore support vessels - the parallel configuration usually wins.
For hybrid vessels, the genset becomes part of a broader power system that includes battery storage, converters and possibly shore charging. The genset sizing in that case is not standalone - it must integrate with the battery management and power conversion systems.
Step 4: Verify Emissions and Class Compliance
The genset must meet the emission limits for the vessel's operating area (IMO Tier II or III, EPA, EU directives) and the class notation requirements. Generator sets destined for workboats and tugs are supplied with type approval documents and factory test reports. Confirm that the genset model - not just the product family - carries the approval for your flag state and class society.
Delivery lead times and warranty terms also belong in the sizing conversation. A genset ordered with type approval documents and factory test reports eliminates the third-party certification step that separate suppliers often require - compressing the timeline between purchase order and commissioning. Standard equipment ships in 15-25 working days; customized builds in 30-45, with no strict MOQ.
FAQ
How do I calculate the total electrical load for a tug or workboat?
Build a consumer list with rated power and duty factor for each item, then tabulate the peak demand for each operating mode (at sea, in port, emergency). Apply a loading factor of 0.8-0.9 and add a future-load margin. The result is the minimum genset rating before class margins.
Should I install one genset or two?
Two smaller gensets in parallel provide redundancy, better part-load efficiency and maintenance flexibility. One larger genset costs less and is simpler. The choice depends on the vessel's reliability requirements and whether losing electrical power for even a short period is acceptable for its trade.
What size genset does a typical harbour tug need?
It depends on the electrical consumers, but harbour tugs typically require gensets in the tens to low hundreds of kW range, driven by hotel load, winches and thruster auxiliaries. The precise rating comes from the load table, not from a rule of thumb.
Can the genset be integrated with shore power and battery systems?
Yes - modern power systems integrate the genset with shore connection, battery storage and power conversion into a single managed system. This improves fuel efficiency and enables zero-emission operation in port.
What documentation comes with the genset?
Type approval documents covering the rated frame, factory test reports, material certificates and the load analysis used for sizing. The documentation package is compiled for survey submission and tender inclusion.
Sizing a genset for a newbuild or retrofit? Request a Quote - engineers reply within 24 hours with a load analysis, genset proposal and type approval documents.